Match the switch to the metal you already have in the room, not to the light fitting. Door handles, sockets and the ironmongery on the windows sit at hand height, in the same glance as the switch, and a switch that agrees with them disappears. One that agrees only with the light on the ceiling does not.
Then check two numbers before you order, because they are what stops a good looking switch going on the wall: how much depth the switch needs behind the plate, and what the dimmer is rated to carry. Both are on the listing and both are below.
The short version
- Match the switch to the handles and the ironmongery at hand height, not to the ceiling light.
- Check the back box depth first. Our toggle switches need 20mm to 23mm behind the plate, our dimmers 25mm.
- A 1 gang or 2 gang plate is 88mm wide; 3 and 4 gang plates are 148mm and need a wider box.
- Our Buster and Punch dimmers take 5W to 120W of LED. Add up the lamps before you choose one.
- Brass is the only finish listed as brass. The other four are stainless steel, and all five carry a PU coating.
The five finishes, and what separates them
The wall switches we stock are Buster and Punch, in five finishes. On the toggle and dimmer listings, brass is the only one whose material is brass; the other four are stainless steel. All five are listed with a PU coating, and smoked bronze adds an aged copper coat under it. So choose on colour and on what is already in the room, not on the metal underneath.
| Finish | Material on the listing (all PU coated) | 1 gang toggle switch | What it suits |
|---|---|---|---|
| Brass | Brass | £51.30 | Warm metals: antique and brushed brass, aged bronze, oak |
| Steel | Stainless steel | £51.30 | Chrome, nickel and cool greys |
| Smoked Bronze | Stainless steel | £51.30 | Dark woods and bronze ironmongery |
| Black | Stainless steel | £46.80 | Matt black handles and modern joinery |
| White | Stainless steel | £46.80 | Plain walls where the switch should not be noticed |
Black and white are the two cheaper finishes: £46.80 for a 1 gang toggle against £51.30 for brass, steel or smoked bronze (checked 16th November 2026). Ten of them come to £468 in black or white and £513 in the other three, so it is worth deciding early rather than switching finish halfway round.
One rule we would hold to. Pick one finish and use it everywhere, including the fused spur by the boiler and the fan isolator outside the bathroom door. A single odd white plate in a room of brass is more noticeable than a room of white plates, because the eye reads the exception rather than the rule.
The measurement that stops a switch fitting
This is the one that catches people, and it is behind the wall rather than on it. Every switch needs a certain depth of back box to sit in, and the deeper the mechanism the more it needs. Some older British houses have shallow boxes, and a switch that needs more depth than the box has will not close flat however hard it is pushed.
| Fitting | Depth it needs behind the plate | Plate size |
|---|---|---|
| Buster & Punch 1G Toggle Switch / Brass | 20mm | 88mm by 88mm |
| Buster & Punch 1G Dimmer / 120W / Brass | 25mm | 88mm by 88mm |
| Buster & Punch 3G Toggle Switch / White | 23mm | 148mm by 88mm |
| Buster & Punch Shaver Socket / Brass | 47mm | 88mm by 148mm |
| Buster & Punch Cooker Switch | 30mm | 149mm by 88mm |
Two things follow. The first is that a dimmer needs more depth than a plain switch, so swapping a switch for a dimmer is not always the like for like job it looks. The second is that the shaver socket needs 47mm, which is a deep box by any standard, so it is worth confirming before the bathroom is tiled rather than after.
If the box behind your switch is too shallow, the fix is to replace the box, which is an electrician's job and a small one. Measure from the face of the wall to the back of the box before you order the switches, and if you cannot, order one switch and try it before committing to the whole house.
Gangs, width and what goes where
A gang is one switch on the plate. A 1 gang plate switches one light or group of lights, a 2 gang two, and so on. The number you need is decided by what is already wired, not by what you would like: a room with one ceiling light and one set of wall lights, switched separately, wants a 2 gang plate.
Width changes at three gangs. The Buster & Punch 1G Toggle Switch / Brass (£51.30, checked 16th November 2026) and the 2 gang toggles are both 88mm square, while the Buster & Punch 3G Toggle Switch / White (£77.40, checked 16th November 2026) is 148mm wide, as are the 4 gang plates. That is a different box and a different hole in the plaster, so a three gang plate is a decision to make before the wall is finished.
Dimmers, and the number on the back
The dimmers in this range take 5W to 120W of LED, the maker's figure, which our dimming guide also quotes. The top of that is a large allowance: a five light pendant with 6W lamps draws 30W, so one dimmer will carry it and two more like it besides. The bottom is the figure that catches people. One 4W lamp on its own is under the 5W minimum, and a dimmer run below its minimum misbehaves.
The rating is only half of it. Whether a light dims smoothly depends on the lamp as much as the dimmer, and a non-dimmable lamp on a dimmer circuit can flicker, strobe or fail to light. We have written the whole of that out in our guide to dimming LED lights, including what to check if a dimmer you already own has started to hum.
One practical note for anyone replacing switches room by room. Our toggle switch listings quote BS EN 60669-1 and the dimmer listings BS EN 60669-2-1, the standards for household switches and for dimmers respectively. We are a merchant, not an electrician: the wiring behind the plate, and whether the job needs notifying where you live, are questions for a registered electrician.
Where a switch is worth the money, and where it is not
A switch is touched more often than any light fitting in the house and it sits at hand height where the finish is seen close up. In a hall, a sitting room or a kitchen that is an easy case to make. In a loft, a garage or a cupboard it is money spent where nobody looks.
The order we would do it in: the rooms you entertain in first, then bedrooms, then the back of the house. Buying a few at a time is fine, provided you settle the finish at the start. Where the switch sits beside a wall light, the two are seen together, so that is the place to let the finish lead, and our guide to mixing metals in one room covers how far to take matching before it starts to look like a showroom.
Frequently asked questions
What light switch finish goes with brass lights?
Brass, if the room has brass ironmongery to go with it. If the handles and window fittings are chrome or nickel, we would match the switch to those and leave the brass to the light fittings. The switch sits at hand height next to the door furniture, so that is the pairing people notice, not the one with the ceiling.
Are designer light switches worth it?
In the rooms you use and show, yes, because a switch is touched several times a day and seen close up, which is not true of most light fittings. In a garage or a loft it is money with nowhere to go. We would do the sociable rooms properly and leave the rest plain rather than do the whole house cheaply.
Will a new switch fit my existing back box?
Check the depth first. Our toggle switches need 20mm to 23mm behind the plate and our dimmers 25mm, and some older houses have shallower boxes than that. Measure from the wall face to the back of the box, or order one switch and try it before buying for the whole house. Replacing a shallow box is a small electrician's job.
How many watts can a dimmer switch take?
The Buster and Punch dimmers we sell take 5W to 120W of LED. A five light pendant with 6W LED lamps draws 30W, well inside that, but one 4W lamp on its own is under the minimum. Add up the wattage of everything on the circuit, and check every lamp is dimmable, because a non-dimmable lamp on a dimmer can flicker or fail to light.
Can I change a light switch myself?
We are a merchant, not an electrician, so we would not tell you to. Fitting a switch means working on mains wiring, the rules on notifying the work differ across the UK, and old or damaged wiring can only show once the plate is off. Have a registered electrician fit it, and give them the depth figures above before they come.







